Sherwood S3000-V Stereo FM Tuner Repair

From the Rain City Audio Repair Blog:

This Sherwood FM Stereo tuner came into the shop recently. It’s owner successfully completed a re-cap of the unit, but the specialized tools for performing an accurate FM Stereo alignment are beyond the reach of most hobbyists, and so he sent it into my shop for final adjustments to make it perfect. The owner reported it worked well on mono, but the stereo light never illuminated, and the dial tracking was a bit off.

The owner had done a good job on the re-cap, with nice clean joints, replacing all but the two output electrolytic caps.

Initial measurements validated the alignment; in mono it was receiving at about 1.6% THD.

Up first was a mono FM alignment, adjusting the cascode RF amplifier, oscillator, and IF chain to bring all the tuned circuits into proper adjustment, improve dial tracking, and center the tuning meter.

After those, and several more adjustments on the bottom side for the lower cores, distortion dropped off to around 0.05% under ideal conditions.

Unfortunately, there was no action on the stereo circuit even when fed from the Sencore SG80 generator. I spent some time tracing out the circuit to understand what’s going on:

One common problem on this style of tuner is that if the stereo indicator lamp has failed, the entire rest of the stereo circuit won’t operate. In this case, the lamp is a NE-2H neon bulb, which can lose its neon with age and fail to strike.

Swapping in a new bulb was the first step.

Success – now the receiver responds to the 19 kHz pilot signal!

Time to finalize the alignment, including the 19 Kc, 38 Kc coils and transformers, the 19 Kc null, and separation adjustment.

The 19 Kc null serves to remove residual 19 KHz audio from the final output signals. It’s adjusted for lowest 19 Kc level which provides proper stereo response.

All set! The indicator light correctly responds to stations transmitting in stereo, and there’s about 10 dB of separation between channels. Much more often just isn’t possible on a tube MPX design. All in all, it sounds great!

This entry was posted in Uncategorized. Bookmark the permalink.

3 Responses to Sherwood S3000-V Stereo FM Tuner Repair

  1. Paul says:

    I replaced an open burned out 1 1/2 amp fuse on a Sherwood S-3000 tuner and it came on and audio works fine.  Driving sound off PC speakers. However the 6BR5/EMBO tube initially worked and the screen beam expanded and responded as signal strength.  However after a few hours of operation only see the filament illuminating the narrow band on the central axis of the phosphor screen but no beam widening on station tuning. 
    What controls the deflection anodes on the tube or has the tube itself gone defective?  Any thoughts on this would be helpful.  Again there is no audio problem, only the loss of 6BR5 beam deflection response on tuning.  All the components on this tuner are original (1959 vintage) and I was surprised it worked at all after being in storage about 40 years.  Yet the fact that the 6BR5 stopped responding suggests another issue that could come up later?  Again all components except the fuse are 1959 original including the can multicap.  I am the only owner and the unit never had work done.

    Any suggestions of which part of the circuit controls the 6BR5 anode?  Seems unlikely that the tube suddenly went defective?  Again filament and phosphor screen raster are intact but only narrow beam on the central screen axis and no tuning response.
    Thank you for any suggestions of how to trouble shoot.
    Paul

  2. Mike DeMeo says:

    Love these stories! I wish you were located near me. I recapped a 1959 Admiral Portable TV, the first one with “Sonr” tuning. It needs an alignment really bad!
    Mike W2MDM

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s